Guide :Radio Communications : Pro-95 Handheld Scanner

Motorola Trunking not working

My PRO-95 was working fine until recently it stopped receiving anything on the trunking network. I tried reprogramming, checking locked out channels, etc. then eventually had to initialize the scanner. It still isn't receiving anything on the Motorola trunking. VHF is working fine. I am getting AM and FM transmissions crossing over on the 800 MHZ frequencies that I am using. The scanner wasn't damaged, but has been left in a hot vehicle at times. Any suggestions? Thank you.

Research, Knowledge and Information :


Digital Radio Problems | Daryl Jones' Weblog


Niagra Regional Police Digital Radio Problems ... radio system not working properly ... statement of no confidence in Motorola digital trunked radio ...
Read More At : blog.tcomeng.com...

Assembled Trunking System (ATS) - Motorola Solutions


To optimize the flow of transmissions, Motorola has developed state-of-the-art trunking technology. Motorola's Assembled Trunking System (ATS) helps your business to ...
Read More At : www.motorolasolutions.com...

Understanding Trunking - Signal Harbor


UNDERSTANDING TRUNKING . ... Motorola. Motorola Type I and ... Scanners on the market today cannot decode the digital voice formats and will not work properly if the ...
Read More At : www.signalharbor.com...

Assembled Trunking System Two-Way Radio Communication ...


Assembled Trunking System Two-Way Radio Communication Solutions. ... That means working ... exceptional quality and functionality of Motorola trunking
Read More At : www.motorolasolutions.com...

Motorola Trunking Radio | eBay


Find great deals on eBay for Motorola Trunking Radio in Commercial Two-Way Radios. Shop with confidence.

Some interfaces/VLAn are not trunking | LAN, Switching and ...


Some interfaces/VLAn are not trunking | LAN, Switching and Routing | Cisco Technical Support Forum | 6016 | 11902141
Read More At : supportforums.cisco.com...

Trunking not working | LAN, Switching and Routing | Cisco ...


Trunking not working | LAN, Switching and Routing | Cisco Technical Support Forum | 6016 | 13327161
Read More At : supportforums.cisco.com...

Regarding Local Area Trunking & Digital - afn.org


Normal analog "trunking" scanners will not work with the local digital trunked communications system. ... Motorola Trunking/ASTRO Training - Motorola;
Read More At : www.afn.org...

A Little Trunking Theory - WiNRADiO Communications


A Little Trunking Theory: ... The radio unit and the working channel perform a high ... the Motorola SmartNet trunking system is theoretically using up to 760 ...
Read More At : www.winradio.com...

Suggested Questions And Answer :


Motorola Trunking not working


If you are getting "cross over" on freqs, then you need to take it in and have it repaired by a pro. You have some bad parts inside and only with the proper electronic gear can you locate them. Plus it will need to be retuned.
Read More At : Pro-95 Handheld Scanner...

My 95 is way off - Freqs,Mode not working...Grrr!


MORE AND MORE POLICE AGENCIES ARE SWITCHING TO "DIGITAL TRUNKING". I CAN ONLY PICK UP PARTS OF MY LOCAL SHERIFFS STATIONS. RADIO SHACK HAS THE NEW dIGITAL TRUNKING SYSTEMS THEY COST ABOUT $500. I AM UP GRADING NOW. FOR TRUNKING ... WHEN YOU GET A ACTIVE CHANNELL KEEP HITTING THE RED TRUNK BUTTON TILL YOU SEE THE MOTOREOLA 5 NUMBEWR ID.THJEN HIT ENTER. I WANT THE NEW PROGRAMER THAT IS FAST ENOUGH TO FOLLOW DIGITAL HYPER-TRUNKING. ALL POLISE ARE GOING TO IT EVENTUALLY.
Read More At : Pro-95 Handheld Scanner...

Pro-95 Internal Speaker not working. External OK


One way to test the speaker, Unsolder 1 of the wires to the speaker terminal, take an ohmmeter and measure the + and - leads of the speaker . if the speaker reads 8 to 32 ohms it is probably not the speaker, if the speaker measures less than 2 ohms or infinity then it is shorted or blown with an open connection. simply replace the speaker with a comparable size, wattage and impedance. I had a similar problem with my pro95, the speaker simply was bad, I replaced it and it was fine. Let me know if you have any questions.. Bob.
Read More At : Pro-95 Handheld Scanner...

Squelch quit working in regular scan mode PRO-528


Just fixed my squelch problem; I don't know how it happened but Resistor 138 was burned & intermittant. It was so badly burned that I could not read the color code but it measured 880 ohms intermittantly. I replaced it with an 860 ohm carbon resistor & all seems well; time will tell. R-138 is located on the circuit board right behind the squelch potentiometer. R-139 is immediately behind the pot & R-138 is next to R-139. All I had to do is remove the 4 screws on the back of the case & the unit splits in half. I clipped the old resistor out leaving a bit of the old leads so I could solder in the new resistor without having to get to the backside of the circuit board. Scanner is working as I type this & I hope it does not burn out again. Hopefully this is the same problem in your scanner & an easy fix. Good luck. Bob Tomlin WB1AIJ
Read More At : Pro-95 Handheld Scanner...

Pro-164 scanner stops receiving when Motorola talk-ids are progra


I had to buy the Radio Shack USB cable 20-047 and install the driver for it and then I downloaded a program named "Win97" from the www.starrsoft.com website as listed on page 21 of the Pro-164 manual. The cable costs $34.99 and with tax you are looking at about $37.88. The "Win97" software must be registered for it to work after a 30-day free trial period. That's approx $25.00. This is the ONLY WAY to go !! You put in everything on the software GUI and then upload it to the PRO-164. Works like a champ !!!!!!
Read More At : Pro-97 Handheld Scanner...

Pro-95 dual trunk-tracking handheld scanner from Radio Shack


Firstly make sure the "squelch" is set as per the manual (link below) page 26. http://support.radioshack.com/support_electronics/doc69/69487.pdf If that fails I suggest initializing the scanner to factory defaults as below:
Read More At : Pro-95 Handheld Scanner...

I have been trying to program Pro 95 for UHF Motorola Trunking


Hi friend,Did u checked ...is there any other channel broadcasting on same frequency,,also check whether any EW transmitting objects placed near it,,,thank u,,,,,,,
Read More At : Pro-95 Handheld Scanner...

Freqs Is there an internal tune i can do. I know the trunked freqs here. They work on other pro-95's. Somehow is is out of tune to the correct trunked freqs. Say my known trunk freq is 868.1275. My radio is getting the trunk @ 869.1265. So somehow my data channel is not tuned. Is there another way to tune get it to sync????


Your scanner has somehow gotten out of alignment, and there's no way to fix it with just a screwdriver. Your best bet for repair is your local Radio Shack. If they can't do the repair they should be able to refer you to a local, or they can ship it off for alignment. Bill B
Read More At : Pro-95 Handheld Scanner...

Pro 97 Handheld - Adapter Issue


I have the same problem with my pro-79 scanner. The adapter from my Uniden cordless phone works on my scanner, but then the phone won''t work. I have rechargeable batteries but they don't stay charged very long in the scanner. I know this didn't solve your problem but thought I would let you know about the cordless phone adapter.
Read More At : Pro-97 Handheld Scanner...

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
next Question || Previos Question
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || radiocomunicate.net || Terms of Use || Contact || Privacy Policy
Load time: 0.1511 seconds