Guide :Radio Communications : MT1000 Compatible 2 Way Radio Battery Eliminator

Mt1000 lock up

It opccurs when changing channels.i suspect there is a higher freq than band split in radio.when it passes that channels.it locks up.....reamains locked up.powering down does no good.shows what looks like 88 in digital display

Research, Knowledge and Information :


HT600/MT1000 - BatLabs


Scanlist Programming for the MT1000. This is a procedure for manual SCAN list programming at MT1000. As you know, a 16ch model of MT1000 can scan 8 ch.
Read More At : batlabs.com...

MT1000 Series - Repeater Builder


MT1000 Series Parts List ... MT1000 AND 99 CHANNEL RADIO REF. NO. PART NO. DESCRIPTION ... TDN9327A Portable Radio Hanger, for Door Panels up
Read More At : www.repeater-builder.com...

SANTAK MT1000 MultiPower MT1000 1000VA (600W) UPS - WECL Online


SANTAK MT1000 MultiPower MT1000 1000VA (600W) UPS Get more details, including price of this item? Click Add below & Send enquiry : Talk ...
Read More At : www.weclonline.com...

Motorola MT1000 - eHam.net Home


Motorola MT1000 eHam.net ... if your MT1000 won't even power up then there's likely not much you can do for it. ... This is the synthesizer lock detect pin, ...
Read More At : www.eham.net...

MT1000 - mouser.com


MT1000 Altera medical-grade, thin wall, semirigid, fluoropolymer heat-shrinkable tubing Altera MT1000 heat-shrinkable tubing is tough, semirigid tubing with a very thin
Read More At : www.mouser.com...

Trimble S8 DR HP FineLock Robotic Total Station 1" Sec TSC3 ...


Details about Trimble S8 DR HP FineLock Robotic Total Station 1" Sec TSC3 Access MT1000. ... This set up is in good condition and ready to go to work.

Dorman Long Technology home page


DL-MT1000 Mega Transporter starts operation in Canada ... Viscous dampers/lock up devices ... Dorman Long Technology India Pvt. Ltd.
Read More At : www.dormanlongtechnology.com...

HT 1000


HT 1000 SYNTHESIZED FM PORTABLE RADI0 Creating New Horizons VHF 85 to 1 Watts 8136-174 MHz UHF 84 to 1 Watts ... having up to two power levels in one radio, and the
Read More At : www.repeater-builder.com...

Suggested Questions And Answer :


Mt1000 lock up


I think there is a problem with the Synthetizer, you will need quilyfied service. This could be caused when you change frequency, the Synth, can not be able to "produce" the desired freq. caused for a problem in this area, this causes to the radios get PLL UNLOCKED and this could be the way that the radio give an alert to the user.
Read More At : MT1000 Compatible 2 Way Radio Battery Eliminator...

Freq lock up


If you have programming cables and SW you can program a freq. in the center of the band,in slimplex. Question, can you read this radio?
Read More At : MT1000 Compatible 2 Way Radio Battery Eliminator...

Battery volts check


With the battery fully charged, you can us a volt meter. Touching the wands to two separate battery contacts. (I believe it to be the outter two. But you will be able to tell from the reaction of your meter.) If it show you a negative number, simply reverse your wands. On the CLS1410 and its sister the VL50, there is a battery indicator built into the radio. It will show you on the screen how much charge is in the batteries. Also, with this style of radio, you are using a Li-Ion battery, which will last you about 12-14 months before you need to replace it. There is a date code on the white portion of the battery label. It is sometimes hard to discern. But if you look you'll see the year followed by the month and date. If the radio was fresh from Motorola when you bought it. The battery date should coincide with its true initial charge age.
Read More At : MT1000 Compatible 2 Way Radio Battery Eliminator...

Display lock up


This happened when try to program the radio en frequencies out of band of radio?
Read More At : MT1000 Compatible 2 Way Radio Battery Eliminator...

I need a manual for Motorola MT1000


You can find part manual on following link: http://www.scribd.com/doc/8782854/MT1000-Userguide for parts details link: http://www.diversifiedelectronics.com/pdf/mt1000.pdf Please post back if it makes any changes. thank you
Read More At : MT1000 Compatible 2 Way Radio Battery Eliminator...

Codeplug locks up during progamming. Seems to read OK, but takes several tries


Is the programming lead ok. No breaks
Read More At : MT1000 Compatible 2 Way Radio Battery Eliminator...

MT1000 Not receiving


Antenna connection inside rf deck may be loose. If that is it, resolder it.. One very common problem that the MT1000 had, along with its littlebrother, the HT600's, was that the antenna lug would break away from theboard. This can usually be repaired by desoldering and resoldering the lugat the PC board end. I do not recommend attempting this repair unless you have the appropriatedesolder/solder tools, and the skill to use same. There is some risk ofdamage to the board if it's not done right.
Read More At : MT1000 Compatible 2 Way Radio Battery Eliminator...

My radio does not turn on - Motorola GP300 Compatible 2 Way Radio Battery Eliminator


Check the battery or the power supply to the circuit, If there is not voltage to the main board this can be failure of the regulator. If not it can be fault in the control circuit. Check the output of the battery eliminator.
Read More At : GP300 Compatible 2 Way Radio Battery Eliminator...

Battery not charging - Motorola GP300 Compatible 2 Way Radio Battery Eliminator


The batteries not charging only means 2 things. the cells in the battery are at their end of life, or the charger's power output is going low because of worn coils or burnt coils.Best deal is to get both pieces tested so you'll have an idea on which one to replace. Battery Care Tips These battery tips will help you obtain optimized performance and a longer life cycle from your Motorola rechargeable battery. 1. Charge your new battery overnight before using it. This is referred to as INITIALIZING and will enable you to obtain maximum battery capacity. a. Nickel Cadmium or Nickel Metal Hydride: 14-16 hours. b. Lithium Ion/Polymer: 1 to 2 additional hours after the charger light turns green. 2. New Motorola impres batteries, when inserted into a Motorola impres charger, will indicate a calibration cycle by displaying a steady Yellow< indication on the charge status indicator. Allow this calibration process to complete by not removing the battery from the charger until it has completely charged and displays a steady green indication. 3. In order to minimize capacity loss and cycle life reduction, new, NON INITIALIZED batteries must be stored in well ventilated, cool and dry locations. Batteries stored in these conditions may be stored: a. Nickel Cadmium up to 2 years. b. Nickel Metal Hydride up to 18 months. c. Lithium Ion/Polymer up to 18 months. 4. If used batteries are to be removed from service for extended periods (greater than 30 days) they should be discharged to about 50% of their capacity before storage in a cool, dry location. 5. Batteries which have been in storage for more than two months should be fully discharged and recharged. a. Nickel Cadmium or Nickel Metal Hydride: 14-16 hours. b. Lithium Ion/Polymer: 1 to 2 additional hours after the charger light turns green. 6. When using a Motorola rapid charger, leave the battery in the charger for an additional 1 to 2 hours after the steady green light appears. (Applies to non-impres batteries only.) 7. Do not leave your radio and fully-charged battery in the charger when not charging. Continuous charging will shorten battery life. (Do not use charger as a radio stand.) 8. Only charge a battery when it needs it. If it is not fully discharged, do not recharge it. We suggest that you carry a spare. This is the most cost effective solution for users requiring longer operating time. 9. Do not return fully charged non-impres batteries to the charger for an "extra boost." This action will significantly reduce cycle life. Repeated short cycle charging of non-impres batteries will shorten battery life. (Do not use charger as a radio stand for non-impres batteries.) 10. Stabilize batteries to room temperature (72ºF) before charging. Charging below 40ºF and above 104ºF will decrease cycle life.
Read More At : GP300 Compatible 2 Way Radio Battery Eliminator...

How to open my motorola gp 300 battery - Motorola GP300 Compatible 2 Way Radio Battery Eliminator


The battery pack for the GP300 radio is a factory sealed unit. There are no user maintainable parts. Sorry! If you are wanting to remove the battery from the radio, look along the sides of the radio near the top. There is a spring-loaded tab on each side. These need pulled down and held while you slide the battery down and off the back of the radio.Best regards.
Read More At : GP300 Compatible 2 Way Radio Battery Eliminator...

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
next Question || Previos Question
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || radiocomunicate.net || Terms of Use || Contact || Privacy Policy
Load time: 0.1245 seconds